Vehicles
Sections
442 not categorized PORSCHE 964 J B ACan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 944 1982-85 (includes uncategorized and accessory items) 99336105700EQ Genuine quality wheel nut and lock set in black. The set includes a key. Please check the exact model designation for this part below. Sold as a set. 1 set necessary per car.
$106.70
Make a selection 99357301103 Condensers release heat from the a/c system, by transforming gas into liquid to absorb heat. Condensers can suffer from internal clogging, seams leaking or can be plugged or damaged by road debris. Be sure to replace as needed to keep the hvac system operating perfectly, especially after a compressor failure. When replacing the condenser, we also recommend replacing the auxiliary condenser fan, part # 96462403501 sold individually. 1 necessary per car.
From $223.30
Make a selection 96453109500EQ This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.
$215.60
Make a selection 99919234350EQ Belts undergo a lot of friction and wear. They are cost effective to change and will keep your alternator and engine in good condition. Be sure to follow recommended service and replacement intervals set by Porsche on belts. For 964 c2 tip trans. / 993 tip trans. / 993 c2/ s manual trans. And the 993 turbo. Sold individually. 1 necessary per car.
$11.00
Make a selection 99660610599 If you are noticing engine vibrations, misfires and even backfiring your crankshaft position sensor maybe bad. Your car's dme (ecu) uses the signal from the crankshaft position sensor to control ignition timing and fuel injection, so if your sensor is failing your engine is suffering from poor timing and is not running efficiently. This kit is complete and ready to install.
$132.75
Make a selection BES96400000T
$17,993.80
Make a selection BEC911964BBC Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$873.40
Make a selection FVD11196415GKT This installation kit is needed to install our part numbers FVD 111 964 15 or FVD 111 964 17. Sold as a set. 1 necessary per car.
$42.90
Make a selection F6464120010 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high quality product similar to your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit is made for global distribution, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. This kit includes faces for: manual transmission / tiptronic transmission / kph / mph / celsi...(choose a part on the right to read more)
$603.90
Make a selection BES96405000S1 This muffler produces a glorious flat six race car with low deep tones that reminds us of the 964 cup. It is manufactured in Germany by m&m exhaust, gmbh. This muffler is ideal for anyone who wants a lower deeper tone with more decibels, whether they are just replacing the side muffler or are running cat bypass, sport cats or a cup pipe. + 14 hp (10 kw) & + 15 tq (20 nm) gain. - 2 3/4 tubing (70mm). - weighs 13.8 lbs (6.3 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions. - includes factory style hangars and new aero quip style clamps for simple installation. We recommend replacing your exhaust tip with this u...(choose a part on the right to read more)
$1,438.80
Make a selection FVD116838 4 puck sintered metallic material which has a higher thermal capacity than organic friction material. Rigid center hub. Aggressive start performance. Hub length 1.18 inches (30mm) outside 1.21 (30.8mm) 240mm weighs: 2.2 lbs (1.01 kg) direct replacement for the oe clutch disc. Made in Germany by zf sachs race engineering. Please note: due the aggressive start performance of the sintered disc, we do not recommend this disc for street cars. We also recommend that you purchase a sport / racing pressure plate in conjunction with this disc. The sachs racing clutch discs with sintered metal plates have a higher friction coefficient than plates with organic friction material. That allows for higher transmittable torque...(choose a part on the right to read more) General Fitment911 GT3 2003-05911 1994-98 968 1992-95 911 1989-94 944 1982-85 944 1985-88
From $477.94
Make a selection FVD111046 Is your exhaust tip a little old and unappealing to look at? Update it with a more aggressive look. Made from t304 stainless steel with a polished finish. 4 round to fill in the entire bumper cut out. Angle cut to complement the rear bumper. Sold individually. 1 necessary per car.
$162.80
Make a selection FVD1609930011 For 380 mm wipers. Sold individually.
$6.60
Make a selection FVD211343 Already replaced your heater blower tube with a carbon bypass? This carbon / kevlar air duct will match the engine decor perfectly. It is a replica of the factory rs lightweight factory air duct. This is a quality tuning product manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. This installs easily and really dresses up the engine. Sold individually. 1 necessary per car.
$267.30
Make a selection FVD205964001
$829.40
Make a selection FVD205964002VA
$449.90
Make a selection FVD205964002HA
$401.50
Make a selection FVD33396400 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,708.55
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$715.00
Make a selection FVD3310212291 Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. -includes press tools and grease for easier assembly. Sold as a set. 1 kit is necessary per car. Please note: this fits the 964 c2 / c4 and rs america. Not keen on installing or having the bushings installed at a shop? Please check out our part # FVD33399603b8 and FVD33399603b8, we wil...(choose a part on the right to read more)
$902.00
Make a selection FVD33396401 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,538.55
Make a selection FVD33396411 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of eibach pro kit springs. This suspension kit is meant for those who want the car to sit at the lowest possible ride height. This set up will allow you to lower the front axle by 2.4 inches (60 mm). This is a perfect kit for clubsport or race use where the surfaces are smooth and even. The stock rs ride height was 1.6 inches (40 mm) lower. So, this is a full 3/4 of an inch (20 mm) lower on the front axle. Sold as a complete kit. 1 kit is necessary per car. Please note: we recommend the b6 / ohlins suspension kits for those looking for more comfort for street use.
$2,616.41
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD34350501 Worn bump stops and bellows can cause premature shock damage. We recommend replacing the stops and bellows with any new shock install. This set includes 2 qty. Front bump stops 96434330100 and 2 qty. Front bellows 96434350500 sold individually. 1 necessary per car.
$104.42
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |